hallogic hall - effect sensors oh090u, OH180U, oh360u ohn3000 series, ohs3000 series ohn3100 series, ohs3100 series ? tt electronics plc issue b 11/2016 page 1 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. descripton: these hall - efect devices contain a monolithic integrated circuit which incorporates a hall element, a linear amplifer, a threshold amplifer, and schmit trigger on a single hallogic? silicon chip. included on - chip is a band gap voltage regulator to allow operaton with a wide range of supply voltages. these devices feature logic level output and provide up to 21 ma of sink current. this allows direct driving of more than 7 ttl loads or any standard logic family using power supplies rangi ng from 4.5 to 24 volts. output amplitude is constant at switching frequencies from dc to over 200 khz. the uni - polar turns on with a (logic level 0) afer a sufcient magnetc feld from the south pole of a magnet approached the symbolized face of the device (operatng point) and turns of (logic level 1) afer the magnetc feld reached a minimum value. the bi - polar latch device turns on (logic level 0) in the presence of a magnetc south pole and turn of (logic level 1) when subjected to a magnetc north pole. both magnetc poles are necessary for operaton for bi - polar devices. this feature makes these sensors ideal for applicatons in non - contact switching operatons, brushless dc motors and for use with multple pole magnets. applicatons: ? non - contact refectve object sensor ? assembly line automaton ? machine automaton ? machine safety ? end of travel sensor ? door sensor features: ? designed for non - contact switching operatons ? operates over broad range of supply voltages (4.5 v to 24 v) ? operates with excellent temperature stability in harsh environments ? drive capability up to 7 ttl loads through hole ordering information through hole configuration ohn3075u ohs3075u ohn3175u ohs3175u ohs3177u bi - polar latching ordering information through hole configuration oh090u OH180U oh360u ohn3113u ohn3019u ohs3019u ohn3020u ohs3020u ohn3120u ohs3120u ohn3030u ohs3030u ohs3130u ohs3131u ohn3040u ohs3040u ohn3140u ohs3140u unipolar non - latching rohs
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 2 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. electrical specifcatons absolute maximum ratngs (t a =25c unless otherwise noted) supply voltage, vcc 25 v storage temperature range, t s - 65c to +160c operatng temperature range, t a ohn30_ _u ohs30_ _u oh090/180/360u - 20c to +85c - 40c to +125c - 40c to +150c lead soldering temperature (1/8 in. (3.2 mm) from case for 5 sec. with soldering iron) 260c (1) output on current, i sink 25 ma output off voltage, v out 25 v magnetc flux density, b unlimited electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) oh090u uni - polar symbol parameter min typ max units test conditions b op magnetc operate point (1) 0 90 180 gauss b rp magnetc release point - 100 65 100 gauss b h magnetc hysteresis 10 25 100 gauss icc supply current - 6 9 ma vcc = 24 v, output of v ol output saturaton voltage - 100 300 mv vcc = 4.5 v, i ol = 20 ma, b 180 gauss i oh output leakage current - 0.5 10.0 a vcc = 24 v, v out = 24 v, b - 100 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 14 v t f output fall time - 0.10 1.00 s OH180U uni - polar symbol parameter min typ max units test conditions b op magnetc operate point (1) 70 180 290 gauss b rp magnetc release point 0 140 230 gauss b h magnetc hysteresis 20 40 120 gauss icc supply current - 6 9 ma vcc = 24 v, output of v ol output saturaton voltage - 100 300 mv vcc = 4.5 v, i ol = 20 ma, b 290 gauss i oh output leakage current - 0.5 10.0 a vcc = 24 v, v out = 24 v, b 0 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 14 v t f output fall time - 0.10 1.00 s notes: (1) south pole facing symbolized surface.
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 3 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. pin # transistor 1 v cc 2 ground 3 output hall element voltage regulator 2 3 1 vcc output ground
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 4 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) oh360u uni - polar symbol parameter min typ max units test conditions b op magnetc operate point (1) 235 300 465 gauss b rp magnetc release point 120 235 325 gauss b h magnetc hysteresis 30 65 200 gauss icc supply current - 6 9 ma vcc = 24 v, output of v ol output saturaton voltage - 100 300 mv vcc = 4.5 v, i ol = 20 ma, b 465 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 120 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 14 v t f output fall time - 0.10 1.00 s ohn3013u, ohn3113u uni - polar symbol parameter min typ max units test conditions b op magnetc operate ohn3013 point (1) ohn3113 - - 300 - 450 510 gauss +25c - 20c to 85c b rp magnetc release ohn3013 point ohn3113 30 20 235 - - - gauss +25c - 20c to 85c b h magnetc hysteresis ohn3013 ohn3113 20 10 65 - - - gauss +25c - 20c to 85c icc supply current - 4 7 ma vcc = 24 v, output of, b 25 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 450 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 25 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s notes: (1) south pole facing symbolized surface.
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 5 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) ohn3019u, ohs3019u, ohn3119u, ohs3119u uni - polar symbol parameter min typ max units test conditions b op magnetc operate oh_3019 point (1) ohn3119 ohs3119 175 100 45 300 - - 500 545 575 gauss +25c - 20c to +85c - 40c to +125c b rp magnetc release oh_3019 point ohn3119 ohs3119 125 50 25 235 - - 450 495 555 gauss +25c - 20c to +85c - 40c to +125c b h magnetc hysteresis oh_3019 ohn3119 ohs3119 50 50 20 65 - - - - - gauss +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b 125 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 500 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 100 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s ohn3020u, ohs3020u, ohn3120u, ohs3120u uni - polar symbol parameter min typ max units test conditions b op magnetc operate oh_3020 point (1) ohn3120 ohs3120 70 70 35 230 - - 350 425 450 gauss +25c - 20c to +85c - 40c to +125c b rp magnetc release oh_3020 point ohn3120 ohs3120 50 50 25 180 - - 330 405 430 gauss +25c - 20c to +85c - 40c to +125c b h magnetc hysteresis oh_3020 ohn3120 ohs3120 20 20 20 50 - - - - - gauss +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b 50 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 350 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 50 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s notes: (1) south pole facing symbolized surface.
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 6 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. notes: (1) south pole facing symbolized surface. electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) ohn3030u, ohs3030u, ohn3130u & ohs3130u uni - polar symbol parameter min typ max units test conditions b op oh_3030 magnetc operate oh_3130 point (1) ohn3130 ohs3130 - - - - 205 - - - 250 150 175 200 gauss +25c +25c - 20c to +85c - 40c to +125c b rp oh_3030 magnetc release oh_3130 point ohn3130 ohs3130 0 - 150 - 175 - 200 160 - - - - - - - gauss +25c +25c - 20c to +85c - 40c to +125c b h oh_3030 magnetc oh_3130 hysteresis ohn3130 ohs3130 20 20 20 20 45 - - - - - - - gauss +25c +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b 0 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 200 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 50 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s ohn3131u & ohs3131u uni - polar symbol parameter min typ max units test conditions b op magnetc operate oh_3131 point (1) ohn3131 ohs3131 - 75 - 75 - 75 - - - 95 95 135 gauss +25c - 20c to +85c - 40c to +125c b rp magnetc release oh_3031 point ohn3131 ohs3131 - 95 - 59 - 135 - - - 85 85 125 gauss +25c - 20c to +85c - 40c to +125c b h magnetc hysteresis oh_3031 ohn3131 ohs3131 10 10 10 - - - - - - gauss +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b 0 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 200 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b 50 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 7 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. ohn3075u, ohs3075u, ohn3175u, ohs3175u bi - polar latch symbol parameter min typ max units test conditions b op oh_3075 magnetc operate oh_3175 point (1) ohn3175 ohs3175 50 25 15 10 100 - - - 250 170 180 260 gauss +25c +25c - 20c to +85c - 40c to +125c b rp oh_3075 magnetc release oh_3175 point ohn3175 ohs3175 - 250 - 170 - 180 - 260 - 100 - - - - 50 - 25 - 15 - 10 gauss +25c +25c - 20c to +85c - 40c to +125c b h oh_3075 magnetc oh_3175 hysteresis ohn3175 ohs3175 100 100 80 50 200 - - - 500 - - - gauss +25c +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b - 250 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 250 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b - 250 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s notes: (1) south pole facing symbolized surface. electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) ohn3040u, ohs3040u, ohn3140u, ohs3140u uni - polar symbol parameter min typ max units test conditions b op magnetc operate oh_3040 point (1) ohn3140 ohs3140 70 45 45 150 - - 220 260 270 gauss +25c - 20c to +85c - 40c to +125c b rp magnetc release oh_3040 point ohn3140 ohs3140 50 25 25 115 - - 180 240 250 gauss +25c - 20c to +85c - 40c to +125c b h magnetc hysteresis oh_3040 ohn3140 ohs3140 20 20 20 35 - - - - - gauss +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b - 50 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 200 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b - 50 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 8 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. notes: (1) south pole facing symbolized surface. electrical characteristcs (vcc = 4.5 v to 24 v, t a = 25 c unless otherwise noted) ohn3177u, ohs3177u bi - polar latch symbol parameter min typ max units test conditions b op magnetc operate oh_3177 point (1) ohn3177 ohs3177 50 25 25 - - - 150 150 200 gauss +25c - 20c to +85c - 40c to +125c b rp magnetc release oh_3177 point ohn3177 ohs3177 - 150 - 150 - 200 - - - - 50 - 25 - 25 gauss +25c - 20c to +85c - 40c to +125c b h magnetc hysteresis oh_3177 ohn3177 ohs3177 100 50 50 - - - - - - gauss +25c - 20c to +85c - 40c to +125c icc supply current - 4 7 ma vcc = 24 v, output of, b - 250 gauss v ol output saturaton voltage - 100 400 mv vcc = 4.5 v, i ol = 20 ma, b 250 gauss i oh output leakage current - 0.1 10.0 a vcc = 24 v, v out = 24 v, b - 250 gauss t r output rise time - 0.21 1.00 s r l = 820 ?, c l = 20 pf, vcc = 12 v t f output fall time - 0.10 1.00 s
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 9 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. typical operate & release points magnetic operate & release points vs temperature oh_3013, oh_3019 & oh_3020 0 50 100 150 200 250 300 350 400 -60c -40c -20c 0c 20c 40c 60c 80c 100c 120c 140c 160c temperature (c) magnetic flux level - gauss oh_3013 release oh_3013 operate oh_3019 release oh_3019 operate oh_3020 release oh_3020 operate magnetic operate & release points vs temperature oh090, oh180 & oh360 0 50 100 150 200 250 300 350 -60c -40c -20c 0c 20c 40c 60c 80c 100c 120c 140c 160c temperature (c) magnetic flux level - gauss oh090 release oh090 operate oh180 release oh180 operate oh360 release oh360 operate magnetic operate & release points vs temperature oh_3030 & oh_3040 0 50 100 150 200 250 -60c -40c -20c 0c 20c 40c 60c 80c 100c 120c 140c 160c temperature (c) magnetic flux level - gauss oh_3030 release oh_3030 operate oh_3040 release oh_3040 operate magnetic operate & release points vs temperature -200 -150 -100 -50 0 50 100 150 200 250 -60 -40 -20 0 20 40 60 80 100 120 140 160 temperature (c) manetic flux level - gauss oh_3177 release oh_3177 operate oh_3075 oh_3075
hallogic hall - effect sensors ? tt electronics plc issue b 11/2016 page 10 tt electronics | optek technology, inc. 1645 wallace drive, ste. 130, carrollton, tx usa 75006 |ph: +1 972 323 2200 www.telectronics.com | sensors@telectronics.com general note tt electronics reserves the right to make changes in product specifcaton without notce or liability. all informaton is subject to tt electronics own data and is considered accurate at tme of going to print. rise & fall time vs temperature 0 50 100 150 200 250 300 350 -40c 0c 40c 80c 120c 150c temperature (c) typical time (ns) rise time fall time saturation voltage vs temperature 0.10 0.15 0.20 0.25 0.30 0.35 0.40 -40c 0c 40c 80c 120c 150c temperature (c) typical saturation voltage (v) r l = 820 ohms icc vs temperature 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 -40c 0c 40c 80c 120c 150c temperature (c) typical icc (ma) icc on (ma) icc off (ma) u.u.t. 820 ohm 20 pf 3 2 1 vcc output ground v ol oh v 10% 90% tr tf 90% 10% b op rp b magnetic field
|
